Download Operation & user’s manual of Eltek Smartpack2 Controller for Free or View it Online on All-Guides.com.
View and Download Eltek Smartpack2 user manual online. Master Controller. About Power System Configuration The Eltek DC power supply system’s functionality represents a vast set of functions, characteristics or capabilities implemented in the hardware and software of the controllers, control units and nodes connected to the system’s CAN.
Page 1 User's Guide Flatpack2 Rectifiers Flatpack2 DC Power Supply Systems 350002.013.; Page 2 4072-2007-AQ-NOR-NA The equipment described in this manual must only be operated by Eltek Valere personnel or by persons who have attended a suitable Eltek Valere training course The equipment represents an energy hazard and failure to observe this could cause terminal injury and invalidate our. About This Revision (2) A new document format was adopted for this revision to reflect the transition to the Eltek Valere brand. In addition, information from individual Flatpack2 system manuals was incorporated into this manual. Smartpack Controller Flatpack2 Power Shelves Controller Expansion Slot Alarm Connections Distribution Section. The most efficient rectifier in the industry, Eltek Flatpack2 Rectifiers combine innovative design, efficiency and reliability. With an efficiency rating over 95%, the losses have been reduced by 50% compared to the current industry standard.
Brand: Eltek
Category: Controller
Type: Operation & user’s manual for Eltek Smartpack2
Pages: 32
28 User's GuideSmartpack2 Master Controller350020.013, Issue 2.0, 2014 Jan
(a)Manual Reset
The DC power system can be configured with automatic or manual alarm reset.
Eltek Smartpack 2 Manual
When Manual Alarm Reset is enabled -- and the alarm condition no longer
exists -- the operator must reset the alarm manually, via the power systems
Eltek Smart Pack 2 Manual
user interface (web GUI or controller’s front keys).
When the Manual Alarm Reset is disabled, then the Automatic Alarm Reset is
enabled (default). In this case, when an alarm condition no longer exists, the
main controller will automatically reset the alarm, by deactivating the alarm
lamps and relays to indicate that normal operation is established.
(b)Hysteresis and Time Delay
(c)Mains Independent
Check this option if you want that the LVD alarm monitor will reconnect the
LVD contactor when the rectifier system output voltage reaches the Reconnect
Voltage limit, regardless whether Mains is ON or OFF. For example, this is
Uncheck this option (Mains dependent) if you want that the LVD alarm
monitor will NOT reconnect the LVD contactor until Mains is ON again.
Used with LVD contactors that disconnect the battery bank (LVBD). Check
this option if you want that the LVD alarm monitor will reconnect the LVBD
contactor when the battery temperature is lower than the temperature limit
(e)Disconnect Voltage
Enter a numeric value for the battery voltage drop-down limit. When -- after a
Mains failure -- the battery voltage gradually drops down to this limit; then the
alarm monitor raises the alarm and trips the LVD contactor.
Enter a numeric value for the battery voltage reconnection limit. When the
Mains supply is ON again, the rectifier system output voltage increases to this
limit; then the alarm monitor will reconnect the LVD contactor.
Enter the Time delay or number of seconds the LVD contactor has to be tripped
or disconnected, before the alarm monitor is allowed to reconnect the LVD
An Alarm Output Group (AOG) is a user defined software assignmentthat consists of
grouping together all the outputs that always are activated at the same time.
The outputs --alarm relay outputs and or latching contactors (LVLD and LVBD) –are
Eltek Flatpack S Manual
distributed among the power system’s controllers and control units.
Related Products for Eltek Smartpack2Related Manuals for Eltek Smartpack2Eltek Integrated Power System ManualEltek Smartpack2: Frequently viewed ManualsComments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |